Skip to main content


United States

Archived content

NOTE: this is an archived page and the content is likely to be out of date.

Fujitsu Now Shipping USB 3.0-SATA Bridge IC for PC Peripherals Supporting SuperSpeed USB 3.0

MB86C30A incorporates USB and SATA signal communication control circuits, protocol and command control circuits with a high-speed encryption/decryption engine on a single device

Fujitsu Semiconductor America Inc.

Sunnyvale, Calif. , July 27, 2009

Fujitsu Microelectronics America, Inc. (FMA) is now shipping its first generation USB 3.0-Serial ATA (SATA) bridge IC, built with Fujitsu’s own physical layer device (PHY). The new MB86C30A supports the ultra-fast 5Gbps maximum data-transfer rate of USB 3.0, and incorporates an encryption/decryption engine. Samples are being built using Fujitsu’s 65-nanometer low-power process technology, and are available now.

Compared with USB 2.0 connections, the MB86C30A bridge IC provides an order of magnitude increase in data transfer rates from external storage devices such as hard disk drives to PCs. The new bridge IC incorporates on a single chip the USB communication control circuits, SATA communication control circuits, and protocol control and command control circuits. These circuits are required to construct an external USB storage device and to realize 5Gbps data transfer to a host PC. (For an example of a system using the MB86C30A, visit this URL:

The MB86C30A IC also contains an embedded Advanced Encryption Standard (AES engine to protect confidential data from being stolen, unintentionally leaked or lost, and to protect data following the disposal of storage devices. Hardware encryption does not burden the CPU of the host PC, and provides optimal protection for data. The encryption/decryption engine enables data to be easily encrypted for secure storage in external devices such as hard disk drives without impairing the performance of USB 3.0.

“The new USB 3.0-SATA bridge IC provides customers with an innovative, reliable, optimized chip design in a small package. Pricing is competitive because we are using our own PHY and process technology,” said Davy Yoshida, director of business development of the Embedded Platform Solutions business group of Fujitsu Microelectronics America. “We expect our chip to be embedded in devices to be released by the end of this year.”

“Fujitsu has applied its extensive expertise in low-power CMOS technologies for high-speed interfaces including Fast Ethernet, Gigabit Ethernet, PCI-express, SATA and IEEE 1394. This IC is the first in the MB86C30 series, which was jointly developed with Fujitsu Laboratories Limited, utilizing their high-speed serial interface technologies, and Fujitsu LSI Solutions Limited. Fujitsu Microelectronics plans to strengthen and expand its lineup of USB 3.0 standard products for storage devices.”

Features Full USB 3.0 Performance with Encryption Capabilities

Today, PCs and audio-visual equipment handle an expanding volume of data from digital photos to audio and video files, requiring storage devices to have increased volumes and speeds. The USB 2.0 interface, which is used widely in external hard drives and memory sticks, has had a maximum data transfer rate of 480Mbps. To provide faster speeds for reading and writing high volumes of data the USB 3.0 specification was ratified in November 2008. USB 3.0 supplies as much as 10 times the data transfer rate of USB 2.0, along with improved protocol efficiency and power management techniques. The maximum transfer rate of 5Gbps of USB 3.0 allows 10 to 30 GBytes of video data to be copied to a 3.5-inch hard disk drive in one-third to one-fourth the time USB 2.0 needs.

The MB86C30A bridge IC supports two AES operation modes: Cipher Block Chaining (CBC), a mode for encrypting block data, and XTS, the XEX encryption mode with tweak and ciphertext stealing. Both modes are ideal for hard disks in terms of security, strength and speed of encryption/decryption. Three key lengths are supported – 128bit, 192bit and 256bit. High-speed encryption and decryption processing at a maximum of 300 MByte/sec. provides throughput without impairing the performance of USB 3.0.


Samples of the MB86C30A manufactured in 65nm CMOS process technology are available now in LQFP 64-pin 7mm x 7mm (0.4mm pitch) packages. Volume pricing is available upon request.

Reference Material

The Fujitsu MB86C30A USB 3.0-SATA bridge IC fact sheet:
High-resolution device photo: (772 KB/USB30
Example of system using the MB86C30A bridge IC:

Product Key Specifications

USB Standard Universal Serial Bus Specification 3.0, Revision 1.0
Universal Serial Bus Specification, Revision 2.0
Bit Rate 5Gbps (SuperSpeed) / 480Mbps (High-Speed)
Device Class Mass Storage Class Bulk-Only Transport, Revision 1.0
SATA Standard Serial ATA Specification Revision 2.6
Bit Rate 3Gbps (Gen2i) / 1.5Gbps(Gen1i)
Encryption Hardware Algorithm AES
Mode CBC / XTS
Block Size 128bit
Key Length 128bit/256bit (CBC mode)
128bit+128bit/256bit+256bit (XTS mode)
Throughput 200MB/s (CBC mode, 128bit)
150MB/s (CBC mode, 256bit)
300MB/s (XTS mode,128bit+128bit)
270MB/s (XTS mode, 256bit+256bit)
Max. Operating Frequency 75MHz
RAM Size 64KByte
Package LQFP 64 pin 7mm x 7mm (0.4mm pitch)
Process Technology 65nm CMOS

About Fujitsu Microelectronics America, Inc.

Fujitsu Microelectronics America, Inc. (FMA) leads the industry in innovation. FMA provides high-quality, reliable semiconductor products and services for the automotive, wireless, industrial, consumer, and other markets throughout North and South America. As a founding member and current board member of the WiMAX Forum™, Fujitsu supports the standards development and compliance programs that are essential to successful Broadband Wireless deployment. Fujitsu provides performance-driven WiMAX solutions by leveraging the company's experience and expertise in the networking and communications markets. Fujitsu offers flexible WiMAX SoC and reference designs for WiMAX-certifiable systems to equipment vendors. For more product information, please visit the company's web site at or address e-mail to

Press Contact - FMA

Emi Igarashi

Phone: Phone: 408-737-5647
E-mail: E-mail:
Company:Fujitsu Microelectronics America, Inc.

ARM7TDMI-S is a trademark of ARM Limited in the EU and other countries.

Other company or product names referenced herein are trademarks or registered trademarks of their respective owners. Information provided in this press release is accurate at time of issue and is subject to change without advance notice.

Date: July 27, 2009
City: Sunnyvale, Calif.
Company: Fujitsu Microelectronics America, Inc.