FUJITSU PLAN EP QL45611 100Gb QSFP28

FUJITSU PLAN EP QL45611 100Gb QSFP28

  • Powerful 100G Ethernet network adapter with 4X25G compatibility
  • Enables network bandwidth to be cost-effectively scaled in support of next-generation server and storage solutions residing in cloud and web-scale data center environments
  • Integrated, advanced networking eliminates I/O bottlenecks and conserves CPU cycles

ImgPlaceholder ImgPlaceholder ImgPlaceholder ImgPlaceholder
Scalable performance
Flexible technology support
Efficient networking
Simplified Management

This Marvell(TM) FastLinQ(R) RDMA RoCE Ethernet network adapter is backward compatible with existing 25GbE installations while allowing an upgrade to 100GbE infrastructure; It provides true hardware-based I/O isolation with unmatched scalability and efficiency

Delivers RoCE v2 technologies and uses a single driver architecture; Recommended as a discrete PCIe adapter for high-density servers.

Increase VM density and accelerate multitenant networks with full offload for tunneling protocols; iSCSI Boot will be commercially supported once the server UEFI is implemented

Works best on UEFI (Unified Extensible Firmware Interface) PRIMERGY and PRIMEQUEST servers; Supports legacy boot as well, however Fujitsu's ServerView Update Tools and iRMC network inventory are not supported on legacy

  • ImgPlaceholder
    Scalable performance
    This Marvell(TM) FastLinQ(R) RDMA RoCE Ethernet network adapter is backward compatible with existing 25GbE installations while allowing an upgrade to 100GbE infrastructure; It provides true hardware-based I/O isolation with unmatched scalability and efficiency
  • ImgPlaceholder
    Flexible technology support
    Delivers RoCE v2 technologies and uses a single driver architecture; Recommended as a discrete PCIe adapter for high-density servers.
  • ImgPlaceholder
    Efficient networking
    Increase VM density and accelerate multitenant networks with full offload for tunneling protocols; iSCSI Boot will be commercially supported once the server UEFI is implemented
  • ImgPlaceholder
    Simplified Management
    Works best on UEFI (Unified Extensible Firmware Interface) PRIMERGY and PRIMEQUEST servers; Supports legacy boot as well, however Fujitsu's ServerView Update Tools and iRMC network inventory are not supported on legacy

Tech Specs

Controller Silicon Cavium QLogic FastLinQ(TM) QL45611 Single-Port 100 Gigabit Ethernet Controller
100 Gbit/s
Connector type QSFP28
Number of Connectors 1
Auto Negotiation support Yes
Bus transfer rate 8GT/s
Network protocol and standards compatibility IEEE 802.1q VLAN, IEEE 802.1Qaz Enhanced Transmission Selection (ETS), IEEE 802.1Qbb Priority Flow Control (PFC), IEEE 802.3x Flow Control, IPv4, IPv6 and mixed IPv4/IPv6 network protocols
LAN controller notes This Ethernet network adapter supports QSFP28 Optical Transceiver Modules for 100 Gbps line rate, or DAC (Direct Access Copper) cables. Interoperable with 10/25/40/50/100Gb Ethernet switches. The component ships with an empty cage. Optical transceivers are commercial options.
HW Virtualization SR-IOV: up to 240 virtual functions, 120 per port, NPAR: up to 16 physical functions, 8 per port
Offloading - TCP Stateless Offloads (include checksum, TSO, TSS, RSS, and RSC)
- TX/RX IP, TCP & UDP checksum offload (IPv4, IPv6) capabilities
Service Weblink https://www.fujitsu.com/emeia/support/
Support Pack Options Globally available in major business areas:
9x5, Next Business Day Onsite Response Time
9x5, 4h Onsite Response Time (depending on country)
24x7, 4h Onsite Response Time (depending on country)
Recommended Service 24x7, Onsite Response Time: 4h - For locations outside of EMEA please contact your local Fujitsu partner.
Support Pack Options Globally available in major business areas:
9x5, Next Business Day Onsite Response Time
9x5, 4h Onsite Response Time (depending on country)
24x7, 4h Onsite Response Time (depending on country)
Recommended Service 24x7, Onsite Response Time: 4h - For locations outside of EMEA please contact your local Fujitsu partner.