Microcontrollers Software |  8-bit MCU Software |  16-bit MCU Software |  32-bit MCU Software |

---

16-bit MCUs Software

The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.

• ADC demonstration

  96340_adc-v12.zip

• ADC-DMA demonstration

  96340_adc_dma-v11.zip

• adc samples continuously an0 to an7 in stop mode

  96340_adc_8ch-v10.zip

• ADC triggered by Reload Timer 1

  96340_adc_rlt-v11.zip

• Bootloader and -manager via USB Host

  96330-usb_bootloader-v13.zip

• Clock output project

  96340_clk_out-v11.zip

• Functionallity of the Alarm Comparator

  96340_alarmcomp-v11.zip

• How to access the external SRAM on the SK-96380-120PMT.

  96380_ext_bus_ram-v10.zip

• How to program, erase an external flash memory.

  96380_ext_bus-v10.zip

• In this demo project, CAN0 will work as a simple repeater.

  90385_can-v13.zip

• In this example the PPG-timer is set to 16-bit mode. There are three different channels.

  90330_ppg16-v11.zip

• In this example the Timebase Timer is used to generate an interrupt every overrun.

  90330_tbt_irq-v11.zip

• Main Flash Erase/Programming example

  96340_flash_main-v10.zip

• Main Flash Erase/Programming example

  96380_flash_main-v10.zip

• Shows how to ruse the DMA with UART0

  96340_dma_uart0-v10.zip

• Shows how to use SD/MM-Cards and USB mass storage support

  96330_usb_mass_storage_spi_sd_card-v12.zip

• Simple demo project showing CAN usage on 16FX microcontroller.

  96340_can-v14.zip

• Template project for MB96326RS

  96320_template_96326rs-v21.zip

• Template project for MB96326RW

  96320_template_96326rw-v21.zip

• Template project for MB96338RS

  96330_template_96338rs-v21.zip

• Template project for MB96338US

  96330_template_96338us-v22.zip

• Template project for MB96345ds

  96340_template_96345ds-v10.zip

• Template project for MB96345dw

  96340_template_96345dw-v10.zip

• Template project for MB96346rs

  96340_template_96346rs-v24.zip

• Template project for MB96346rw

  96340_template_96346rw-v26.zip

• Template project for MB96347rs

  96340_template_96347rs-v24.zip

• Template project for MB96347rw

  96340_template_96347rw-v24.zip

• Template project for MB96348hs

  96340_template_96348hs-v25.zip

• Template project for MB96348hw

  96340_template_96348hw-v25.zip

• Template project for MB96348rs

  96340_template_96348rs-v23.zip

• Template project for MB96348rw

  96340_template_96348rw-v23.zip

• Template Project for MB96355rs

  96350_template_96355rs-v12.zip

• Template Project for MB96355rw

  96350_template_96355rw-v12.zip

• Template Project for MB96356rs

  96350_template_96356rs-v26.zip

• Template Project for MB96356rw

  96350_template_96356rw-v26.zip

• Template Project for MB96379rs

  96370_template_96379rs-v17.zip

• Template Project for MB96379rw

  96370_template_96379rw-v16.zip

• Template project for MB96386rs

  96380_template_96386rs-v22.zip

• Template project for MB96386rw

  96380_template_96386rw-v22.zip

• Template project for MB96387rs

  96380_template_96387rs-v22.zip

• Template project for MB96387rw

  96380_template_96387rw-v22.zip

• The channels 0/2/4 of the PPG-timer are used to deliver the count clock for channels 1/3/5.

  90330_ppg88-v11.zip

• The I2C-Interface 0 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)

  90330_i2c_0-v12.zip

• The I2C-Interface 1 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)

  90330_i2c_1-v12.zip

• The I2C-Interface 2 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)

  90330_i2c_2-v12.zip

• This example shows functionality of the CAN-controller (CAN0/1). It is controlled by a terminal on UART0.

  96330_can_uart_terminal-v10.zip

• This example shows functionality of the CAN-controller (CAN0). It is controlled by a terminal on UART0.

  96340_can_uart_terminal-v13.zip

• This example shows how ReloadTimer 1 can be used to generate the Baudrate of UART 1.

  90385_uart1_rlt1-v10.zip

• This is a demo project for the FLASH-CAN-48P-M26 (-90F387) evaluation board.

  90385_flashcan48pm26-v13.zip

• This is an example of the output compare function.

  90330_frt_ocu-v11.zip

• This is a project for the MB90385 Series to show the usage of external interrupts.

  90385_irq_ext-v10.zip

• This is a project template for the MB90330 Series.

  90330_template-v12.zip

• This is a project template for the MB90335 Series.

  90335_template-v13.zip

• This is a project template for the MB90385 Series.

  90385_template-v16.zip

• This is a sample project for access to main and satellite Flash of the MB96340 Series in a uniform manner.

  96340_flash_main_satellite-v10.zip

• This is a software example to test the four channels input compare of the 90330 Series (Simple frequency counter)

  90330_frt_icu-v12.zip

• This is a test application to echo characters received via UART1 using RX IRQ.

  90385_uart1_async_irq-v10.zip

• This is a test application to measure the frequency of an input signal on PWC-input pin and send the result to UART0

  90330_pwc_uart_async-v13.zip

• This is a test application to send a welcome string via UART0.

  90330_uart0_async-v14.zip

• This is a test application to send a welcome string via UART0.

  90330_uart0_async_irq-v13.zip

• This is a test application to send a welcome string via UART1.

  90330_uart1_async-v13.zip

• This is a test application to send a welcome string via UART2.

  90330_uart2_async-v13.zip

• This is a test application to send a welcome string via UART3.

  90330_uart3_async-v13.zip

• This is a test application which sends a welcome string via UART1 and echoes every received character.

  90385_uart1_async-v13.zip

• This project contains a boot strap loader and can be used to create application specific bootloaders.

  90385_bootloader_uart1_async-v10.zip

• This project contains a boot strap loader and can be used to create application specific bootloaders.

  96340_bootloader_uart_async-v11.zip

• This project contains a boot strap loader and can be used to create application specific bootloaders.

  96380_bootloader_uart_async-v10.zip

• This project contains an interface function to demonstrate LCD.

  96380_lcd-v10.zip

• This project demonstrates routout of internal chipid.

  96380_chipid-v10.zip

• This project is a demonstration of the Watchdog Timer

  90330_wdt-v11.zip

• This project simply counts an internal variable and outputs the counter value to LEDs on starterkit FLASH-CAN-48P-M26.

  90385_io-v12.zip

• This project simply counts an internal variable and outputs the counter value to port0.

  90330_io-v11.zip

• This project simply shifts a '1' up and down on port0, controlled by INT0 and INT1.

  90330_irq_ext-v12.zip

• This projects shows how to use EIIOS with UART interface.

  90385_uart1_async_eiios-v11.zip

• This project uses interrupts of reload-timer0 and reload-timer1 to toggle port 1 (LEDs on FLASH-CAN-64P-LQFP48).

  90385_rlt_irq-v12.zip

• This project uses interrupts of reload-timers 0-2 to toggle LEDs (Port0).

  90330_rlt_irq-v11.zip

• This sample uses an Analog - Digital conversion

  90330_adc-v12.zip

• This sample uses an Analog - Digital conversion and UART0

  90330_adc_uart_async-v12.zip

• USB-Host demo incl. mass storage class with FAT16 filesystem to support USB Mass Storage Devices on MB96330U Series.

  96330_usb_mass_storage_demo-v13.zip

  Previous Page      1       2     3     4      Next Page