DESCRIPTION

To install the Software Sample Files please download the compressed self-extracting file. The Standard Installation Target Directory is:

C:\Softune\sample\smpl16

FEATURES

• ADC_sing Project:
  It includes some basic settings for e.g. Linker, C-Compiler which must be checked and modified in detail, corresponding to the user application.
• ADCEII_sm Project:
  This is to use the AD converter in single mode, using EIIOS. It includes some basic settings for e.g. Linker, C-Compiler which must be checked and modified in detail, corresponding to the user application.
• ADCInt_sm Project:
  It includes some basic settings for e.g. Linker, C-Compiler which must be checked and modified in detail, corresponding to the user application.
• Bootloader Project:
  For the time being the binary of the MB90F594 bootloader can be used. As long as UART0 is set for MB90F594 it is fully compatible with MB90F598.
• CAN Project:
  CAN0 will work as a simple Repeater. Received data will appear at Port P47..P40 (UserLEDs of FlashCan100P) and will send out again as byte-packages to ID#2 Receive-Buffer #1 : basic can Transmit-Buffer #6 : full-can ID #2
• CAN_Accemic:
  same as CAN Project, but works with Accemic MDE
• CANmanag:
  tiny CAN Management (requires Softune IDE >= SoV30L27): This is a demoprogram for to a simple network management for CAN. Up to 32 nodes can be configured. Each node connects automatically to the network. All nodes make a logic ring.
• Icu0 Project:
  It initializes the input capture0. Also the 16bit Free RunningTimer.
• IOPORT Project:
  IOPort-project simply counts down an internal variable and outputs the counter value to port1. No interrupts are used.
• OcIc0 Project:
  It initializes the input capture0 and the output compare unit 0. Also the 16bit Free RunningTimer.
• Ocu03 Project:
  It initializes the output compare units 0-3. Also the 16bit Free RunningTimer.
• PPG Project:
  Interrupt service routine of Reload-timer0 is used to modify PPG channel 1.
• Ppg16 Project:
  Interrupt service routine of Reload-timer0 is used to modify PPG channel 1.
• PPG2x8 Project:
  Interrupt service routine of Reload-timer0 is used to modify PPG channel 1 and channel 3.
• PPG8+8 Project:
  It initializes the PPG0 and PPG1.
• Reload Project:
  Reload-project uses interrupts of reload-timer0 and reload-timer1 to toggle LEDs.
• RLT595_Loader Project:
  This is a demoprogram for to initialize the Reload Timer 0 and relaod Timer 1 of the MB90595 Series. Interrupts are used to toggle two ports corresponding to the Reload Timer interrupts.
• SIO Project:
  It initializes the SIO to output a byte with intern clock synchronisation.
• Template Project:
  It includes some basic settings for e.g. Linker, C-Compiler which must be checked and modified in detail, corresponding to the user application.
• Timermode test:
  This is a project to set the MB90F598 into timer mode. The wake up is done via external interrupt INT0, which must be programmed active high.
• UART Project:
  This is a simple demo program to initialize and use the UART interface.
• Watch_DOG:
  When starting a "LED-line" is built up.at Port 4; when Flash-CAN100 is used When all LEDs are on, then Watch-Dog is started. The application will toggle LED D0 (P40). Blink-time (delay) will be increased automatically. If "delay" is larger than the Watch-Dog time, then the watchdog-unit will restart the microcontroller. When the emulator is used, within Debug-Environment / Chip => Watchdog enable has to be set !
• History of the MB90595:

DOWNLOAD

Note: Netscape Navigator 4.xx does not allow direct execution of ".exe" files. Saving them to a temporary folder and executing them there is recommended.

EXESelf-extracting Sample Files for MB90595 Series V01R08 (980 KB, 11.September 2006)