DESCRIPTION

To install the Software Sample Files please download the compressed self-extracting file. The Standard Installation Target Directory is:

C:\Softune\sample\smpl16

FEATUTRES

• Template
  This is a project template for the MB90560 Series. It includes some basic settings for e.g. Linker, C-Compiler which must be checked and modified in detail, corresponding to the user application.
• ADCInt
  This is a ADC project sample for the MB90560 Series. It shows how to use ADC with interrupts.
• ADCReload
  This is a ADC project sample for the MB90560 series. It shows how to use ADC with the Relaod Timer.
• Flash64P
  This exampel project uses the reload timer interrupts and outputs a string on UART0 and UART1.
• FlashWrite
  This sample project demonstrates the programming of the internal flash memory. The routines itself are executed in RAM. The code is permanently located in RAM during run-time.
• Gate_PPG
  The example initialises the output compare units0-5,the PPG0-5. Also the 16bit Free RunningTimer and Waveform generator. The program shows how to initialize a gated PPG output. During a 'H' level of an OCU the PPG is generating an output signal.
• ICU03
  This example program initialises the input capture units 0-3. Also the 16bit Free RunningTimer is initialised.
• IOPort
  IOPort-project simply counts down an internal variable and outputs the counter value to port4.
• OCU
  In this examples the output compare units 0-5 are used together with the 16bit Free RunningTimer.
• OCU+PPG
  In this example the output compare units 0-5, the PPG 0-5 are initialised. Also the 16bit Free RunningTimer is used.
• OCU+wave
  In this example program the output compare units 01 are used. Also the 16bit Free-run Timer and Waveform generator (dead timer function), generating non-overlay signal by using OCU01 and Waveformgenerator.
• PPG Inistialises
  PPG channel 1 and uses Interrupt service routine of Reload-timer0 to modify duty cycle of PPG channel 1.
• PPG01
  It initializes the PPG channel 0 and 1. The operating modes of the PPGs can also be set in the corresponding function call.
• PPG05
  Simply initialises the PPG0 - PPG5.
• PPG8+8int
  It initialises the PPG0-5 in 8+8bit mode. The lower 8-bit PPG channels (0,2,4) are used as prescaler for the upper 8bit PPG channels (1,3,5). The interrupts of Channel 1,3,5 are activated.
• Reload
  Simple Demoproject using interrupts of reload-timer0 and reload-timer1 to toggle two LEDs.
• Test560
  Simply generates some line patterns to be output on Port0.
• TimerPPG
  It initializes the output compare units01,the PPG01. Also the 16bit Free RunningTimer and Waveform generator. The example shows you the oeration of PPG and GATE signal Control Circuit ( TIMER mode ) The PPG is gated by the 8-bit timers. A rising edge of a RT-signal starting the 8-bit timer, which is counting up to stop value. The PPG-signals are outputting at RTO during this time.
• UART0560
  It initializes the UART0 to output a welcome String. Also it echos every receiving character.
• UART1_syn
  This program initialises UART1 to be used in sysnchronous transmision mode.
• UART1560
  It initializes the UART1 to output a welcome String. Also it echos every receiving character.
• Stop_mode
  Example Project to show how to enter Stop mode and to release from stop mode using an external Interrupt.
• History of the MB90560:

DOWNLOAD

Note: Netscape Navigator 4.xx does not allow direct execution of ".exe" files. Saving them to a temporary folder and executing them there is recommended.

EXESelf-extracting Sample Files for MB90560 Series V01R04 (792 KB, 11.September 2006)