• Product Features
• Documentation
• Starterkits
• Debugger and Emulator
• (FLASH-)ROM Programming Tools
• Software Examples
• Application Notes

SERIES KEY FEATURES

DESCRIPTION

BLOCK DIAGRAM

DOCUMENTATION

STARTERKITS

• Starterkit
• Starterkit
• Starterkit

DEBUGGER and EMULATOR

Monitor Debugger

• Monitor Debugger

  Accemic-MDE

Power Supply Unit for Starterkit 1

• EVA-Chip EVA-Chip
  MB91V265CR-ES

• Emulation Pod/Adapter
  MB2198-130-E

• Socket
  NQPACK064SB, HQPACK064SB140

• Power Supply Unit for Starterkit
  POWERED BY BATTERIES

• Accessory Kit

  ACCESSORIES32

• Emulation Main Unit

  MB2198-01-E

• Probe Cable

  MB2198-128-E

• Starterkit

  Phase3-Kit

Power Supply Unit for Starterkit 2

• EVA-Chip EVA-Chip
  MB91V265CR-ES

• Emulation Pod/Adapter
  MB2198-130-E

• Socket
  NQPACK064SB, HQPACK064SB140

• Power Supply Unit for Starterkit
  DEPENDING ON APPLICATION, LABORATORY POWER SUPPLY RECOMMENDED

• Accessory Kit

  ACCESSORIES32

• Emulation Main Unit

  MB2198-01-E

• Probe Cable

  MB2198-128-E

• Starterkit

  MotorKit-91F267-MC

(FLASH-)ROM Programming Tools

• FLASH_PROGRAMMER_FR_FJ

  serial (async)

SOFTWARE EXAMPLES

The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment. Additional motor control related software examples can be found at the MotorKit-91F267-MC page (section: MB91F267NPMC - STARTERKITS)

• Character read from UART and send via CAN .
• LED is toggled by using RLT-interrupt.
• PWC is used to determine the frequency of a rectanculary signal.
• This Example converts the Value at AN8 to a digital value with 8 Bit resolution.
• This example does a simple string output on UART0.
• This Example initializes ADC channel8. The converted value is stored to a buffer by DMA-transfer.
• This example stores a typed string to Flash and reads it. It is controlled by a command line interface.
• This is an example project for controlling an AC-inverter.
• This is an example project for external interrupts.
• This is an example project for using PPG.
• This is a project template for the MB91265 Series.
• This is a simple demonstration for the MAC unit of the MB91265 Series.
• This is a simple demonstration for the MAC unit of the MB91265 Series. It applies a sequence to a digital filter.
• This project simply counts an internal variable and outputs the counter value to port5.

All software examples

APPLICATION NOTES

Please find a selection of Application Notes here or check the complete overview. Additional motor control related application notes can be found at the MotorKit-91F267-MC page (section: MB91F267NPMC - STARTERKITS)

• This Application Note describes how to setup the Softune Workbench to automatically start the debugger at start.
• This application note explains the usage of the 16-bit MAC-Unit.
• This application note gives an introduction to the MB91265 Series Multi-Function Timer and its usage for motor control.
• This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully
• This application note shows a simple method to control a BLDC motor using an encoder.
• This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG.
• This application note will help you how to debug the application with Softune Workbench V6 Simulator. The simulator debugger simulates the MCU operations (executing instructions, memory space, I/O ports, interrupts, reset, etc.) with software to evaluate a program.

All application Notes