MB95200 Series : MB95200 Series : MB95F203KPGSHSNE2
SERIES KEY FEATURES
DESCRIPTION
Fujitsu MB95200 series of microcontrollers are 8-bit general purpose single-chip products providing precise on-chip oscillators, single-wire debug, clock supervisors, low voltage reset (option) as well as various peripherals for applications like air conditioner, remote controller, digital/pocket photographic materials, refrigerator, washing machine,electronic oven, etc.
BLOCK DIAGRAM
PRODUCT FEATURES
| Specification | Description |
| CPU [Bits] | 8 |
| Package | DIP-24P-M07 |
| Pincount | 24 |
| Flash memory | 8.00 KByte |
| Flash Security (read protection) | yes |
| RAM (code & data) | 0.50 KByte |
| VCC min | 2.40 V |
| VCC max | 5.50 V |
| Min. Temperature | -40 °C |
| Max. Temperature | 85 °C |
| Max. CPU frequency | 16.25 MHz |
| Subclock | yes |
| Clock Supervisor | yes |
| Max. I/Os | 17 |
| A/D Converter | 1 |
| A/D channels | 6 |
| A/D resolution | 10 bit |
| LIN-USART | 1 |
| Programmable Pulse Generator (PPG) | 2 |
| Pulse Width Modulator (PWM) | 1 |
| Output Compare Unit (OCU) | 1 |
| Input Capture Unit (ICU) | 1 |
| Watchdog | 1 |
| Low Voltage Detection (LVD) | yes |
| External IRQ | 6 |
DOCUMENTATION
- Datasheet
ds95200h-ds07-12623-4e
- Hardware Manual
hm95200h-cm26-10123-1e
- Programming Manual
prog8fx-cm26-00301-2e
STARTERKITS
- Starterkit
MB2146-410A-01-E
DEBUGGER and EMULATOR
Power Supply Unit for Starterkit
POWERED BY USB- Starterkit
MB2146-410A-01-E
(FLASH-)ROM PROGRAMMING TOOLS
- Name: FLASH_PROGRAMMER_USB_LPC
Adapter: MB2146-08-E
APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
- The Application Note describes the function and operation of low-voltage detection reset circuit.
- This application note describes flash operation in MB95200H/210H Series.
- This application note describes how to set and use the External Interrupt.
- This application note describes how to start development with the Fujitsu F2MC-8FX Family MB95200H/210H Series.
- This application note describes how to start up the basic FW setting of the Fujitsu F2MC-8FX Family MB95200H/210H Series.
- This application note describes how to use 8/10-bit A/D converter in each mode.
- This application note describes how to use DBG pin.
- This application note describes how to use IO Port.
- This application note describes how to use the 8/16-bit composite timer in various modes.
- This application note describes how to use the Fujitsu’s LIN USART to control LIN devices (e.g.: AMIS-30621 stepper motor driver).
- This application note describes how to use the LIN-UART in various modes.
- This application note describes how to use the watch-dog timer.
- This application note describes how to use the wild register function.
- This application note describes the Flash Security.
- This application note describes the functions and operations of Clock Supervisor Counter.
- This application note describes the main CR clock configuration and the CR trimming function.
- This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully
- This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG.
