MB95130 Series : MB95F136JBWPFV
- Product Features
- Documentation
- Starterkits
- Debugger and Emulator
- (FLASH-)ROM Programming Tools
- Software Examples
- Application Notes
SERIES KEY FEATURES
DESCRIPTION
The MB95130 Series has been developed as a general-purpose version of the F2MC*-8FX family consisting of proprietary 8-bit
single-chip microcontrollers. In addition to a compact instruction set, the FLUTE Series is general-purpose, single-chip microcontrollers
with a wide range of internal peripheral functions.
MB95130H Series : 5V version
BLOCK DIAGRAM
PRODUCT FEATURES
| Specification | Description |
| CPU [Bits] | 8 |
| Package | FPT-30P-M02 |
| Pincount | 30 |
| Compact Flash | 32.00 KByte |
| Flash Security (read protection) | yes |
| RAM (code & data) | 1.00 KByte |
| VCC min | 2.88 V |
| VCC max | 5.50 V |
| Min. Temperature | -40 °C |
| Max. Temperature | 85 °C |
| Max. CPU frequency | 16.25 MHz |
| Subclock | yes |
| Clock Supervisor | yes |
| Max. I/Os | 18 |
| A/D Converter | 1 |
| A/D channels | 8 |
| A/D resolution | 10 bit |
| A/D conversion time (min.) | 1.200 µs |
| UART | 1 |
| LIN-USART | 1 |
| Programmable Pulse Generator (PPG) | 2 |
| Pulse Width Modulator (PWM) | 1 |
| Timer Counter | 2 |
| Timebase Timer (TBT) | 1 |
| Watchdog | 1 |
| Low Voltage Detection (LVD) | yes |
| External IRQ | 8 |
DOCUMENTATION
- Datasheet
ds95130mb-ds07-12621-2e
- Hardware Manual
hm95130mb-cm26-10118-2e
- Hardware Manual Correction
hm95130mb-cm26-10118-2et3
- Package datasheet
fpt-28p-m17
- Programming Manual
prog8fx-cm26-00301-2e
STARTERKITS
DEBUGGER and EMULATOR
EVA-Chip EVA-Chip
MB95FV100D-103PBTPower Supply Unit for Starterkit
INCLUDED- Accessory Kit
ACCESSORIES8FX
- Emulation Main Unit
MB2146-09A-E
- Package Conversion Adapter
MB2146-271
- Starterkit
MB2146-401
- Starterkit Adapter
MB2146-303A-E
(FLASH-)ROM PROGRAMMING TOOLS
- FLASH_PROGRAMMER_8FX
serial (async)
SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
APPLICATION NOTES
Please find a selection of Application Notes here or check the complete overview:
- Customer information to inform about LIN conformance tests
- How to use the Softune Workbench Monitor Debugger for 8FX.
- This application note describes how to program the Flash device MB951xx in serial async mode.
- This application note describes how to program the Flash device MB951xx in serial sync mode by use of MB2146-09.
- This Application Note describes how to setup the Softune Workbench to automatically start the debugger at start.
- This application note describes how to use the Fujitsu’s LIN USART to control LIN devices (e.g.: AMIS-30621 stepper motor driver).
- This application note describes the most common SPI formats and how to implement them on Fujitsu 16-bit MCUs.
- This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully
- This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG.
- This appnote for the 8L Family gives hints to optimize the EMI performance.
- This document describes how to set up a new project for the 8FX Family.
- This installation guide will help you set up the MB2146-09 BGM adapter with the MB2146-301 or MB2146-303 MCU board for Fujitsu 8FX microcontroller and its usage with 8-bit Softune Workbench V30L29 or higher.
