• Product Features
• Documentation
• Debugger and Emulator
• (FLASH-)ROM Programming Tools
• Software Examples
• Application Notes

SERIES KEY FEATURES

DESCRIPTION

BLOCK DIAGRAM

DOCUMENTATION

DEBUGGER and EMULATOR

Monitor Debugger

• Monitor Debugger

  Accemic-MDE

Emulation Main Unit

• EVA-Chip EVA-Chip
  MB90V330ACR-ES

• Socket
  NQPACK120SD, HQPACK120SD

• Accessory Kit

  ACCESSORIES16

• Emulation Main Unit

  MB2147-01-E

• Emulation Pod/Adapter

  MB2147-20-E

• Probe Cable

  MB2132-492

(FLASH-)ROM Programming Tools

• CONITEC GALEP
  serial
  Conitec 210865/210915

• FLASH_PROGRAMMER_16LX

  
  serial (async)

SOFTWARE EXAMPLES

The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.

• In this example the PPG-timer is set to 16-bit mode. There are three different channels.
• In this example the Timebase Timer is used to generate an interrupt every overrun.
• The channels 0/2/4 of the PPG-timer are used to deliver the count clock for channels 1/3/5.
• The I2C-Interface 0 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)
• The I2C-Interface 1 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)
• The I2C-Interface 2 of the MB90330-Series is used to write and read data from an external EEPROM (24C16)
• This is an example of the output compare function.
• This is a project template for the MB90330 Series.
• This is a software example to test the four channels input compare of the 90330 Series (Simple frequency counter)
• This is a test application to measure the frequency of an input signal on PWC-input pin and send the result to UART0
• This is a test application to send a welcome string via UART0.
• This is a test application to send a welcome string via UART0.
• This is a test application to send a welcome string via UART1.
• This is a test application to send a welcome string via UART2.
• This is a test application to send a welcome string via UART3.
• This project is a demonstration of the Watchdog Timer
• This project simply counts an internal variable and outputs the counter value to port0.
• This project simply shifts a '1' up and down on port0, controlled by INT0 and INT1.
• This project uses interrupts of reload-timers 0-2 to toggle LEDs (Port0).
• This sample uses an Analog - Digital conversion
• This sample uses an Analog - Digital conversion and UART0

All software examples

APPLICATION NOTES

Please find a selection of Application Notes here or check the complete overview:

• First steps how to use the Emulator MB2147-01 together with the Softune Workbench V30L28 or higher using an evaluation MCU with its Starter Kit.
• How to set up a hardware environment for 16LX Family MCUs.
• Recommendation for MODE-Pins in case of external noise
• This Application Note describes how to setup the Softune Workbench to automatically start the debugger at start.
• This application note describes how to use the Fujitsu’s Softune with EasyCode
• This application note describes the commands which are supported by the BiROM of the 16LX Flash MCUs in order to generate an own programming environment.
• This application note describes the most common SPI formats and how to implement them on Fujitsu 16-bit MCUs.
• This application note describes the setup and using of a third party Flash programmer, CONITEC's GALEP-5
• This application note explains the different possibilities to program the Flash MCUs.
• This application note gives a rough overview about the embedded A/D converter used within the 16LX Series and reflects the different modes that can be used.
• This application note provides some information and recommendations how to connect external crystals or resonators to Fujitsu microcontrollers. In order to achieve a proper and stable clock oscillation the composition of external circuits, PCB layout design and the microcontroller must be taken into account and evaluated carefully
• This application note reflects the external bus interface that can be found on some devices of the 16LX Series.
• This application note roughly shows the necessary steps for transition to standby-mode and wake-up for 16LX Family MCUs.
• This application note shows some possibilies to drive a BLDC motor with different MCUs using a single PPG.
• This appnote for the 16LX Family gives hints to optimize the EMI performance.
• This document describes the debugging methods of a MB90V340 system together with a FLASH-CAN-100P-340 target board.
• This installation guide will help you to quickly start setting up the MB2147-01 emulation hardware for Fujitsu 16-bit MCUs.
• This is a sample project for access to satellite Flash of the MB96340 Series.
• This is a short documentation to give an introduction how to start a project with the Softune Workbench.

All application Notes